TGR6000 AIM-TTI射频信号发生器6GHz_信号发生器

产品展示

您当前的位置：首页 » 产品展示 » 信号发生器 » TGR6000 AIM-TTI射频信号发生器6GHz

产品名称：	TGR6000 AIM-TTI射频信号发生器6GHz
产品型号：	TGR6000
品牌：	1532
产品数量：
产品单价：	面议
日期:	2024-09-19

TGR6000 AIM-TTI射频信号发生器6GHz的详细资料

AIM-TTI射频信号发生器6GHz
AIM-TTI射频信号发生器6GHz
AIM-TTI射频信号发生器6GHz
TGR6000信号发生器,英国tti TGR6000：
6GHz RF Signal Generator

10MHz to 6000MHz frequency range
10Hz setability, +/-1ppm frequency stability
Locking to external frequency standard
-110dBm to +7dBm amplitude, 0.1dB steps
Fast stepping sweep with dwell times down to 10ms
List sweep of up to 1000 points of amplitude vs frequency
User compensation tables for specific test set-ups
Storage for 12 generator set-ups and 16 sweep lists
Compact half-rack 2U casing uses minimum bench space
Full remote control through RS232, USB, LAN and GPIB
Significantly lower cost than other 6GHz generators

TGR6000信号发生器,英国tti TGR6000：
Aim-TTi TGR6000 6GHz RF Signal Generator

The TGR6000 is a low-cost 6GHz signal generator intended for CW (carrier wave) applications where modulation is not required. Low phase noise is matched by low leakage, low residual FM and spurii. The internal timebase has a 1ppm stability, and an external frequency reference can be used. Sophisticated sweep functions enable the frequency and/or amplitude to be swept over the full range of each in a single sweep.

0MHz to 6000MHz frequency range
10Hz setability, +/-1ppm frequency stability
Locking to external frequency standard
-110dBm to +7dBm amplitude, 0.1dB steps
Fast stepping sweep with dwell times down to 10ms
List sweep of up to 1000 points of amplitude vs frequency
User compensation tables for specific test set-ups
Storage for 12 generator set-ups and 16 sweep lists
Compact half-rack 2U casing uses minimum bench space
Full remote control through RS232, USB, LAN and GPIB
Significantly lower cost than other 6GHz generators

TGR6000信号发生器,英国tti TGR6000：

Technical specification
Frequency
Frequency Range	10MHz to 6000MHz
Setting Resolution	10Hz by direct keyboard entry, or in user-set increments of 10Hz to 999•999MHz by rotary control or increment–decrement keys
Phase Noise	500MHz Carrier: <-110dBc/Hz @ 20kHz offset; <-120dBc/Hz @ 100kHz
	3GHz Carrier: <-95dBc/Hz @ 20kHz offset; <-110dBc/Hz @ 100kHz offset
	6GHz Carrier: <-89dBc/Hz @ 20kHz offset; <-104dBc/Hz @ 100kHz offset
Residual FM	Equivalent peak deviation for 300Hz to 3.4kHz B/W: 12Hz at 500MHz carrier
Settling Time	<8ms to settle within 100Hz or 0.1ppm of final frequency, if greater
Reference Frequency	Internal or External (via rear panel BNC)
Internal Accuracy	+/- 1 ppm over 15°C to 30°C; +/- 2 ppm over 5°C to 40°C
Internal Stability	< +/-1ppm/year ageing
Internal Ref. Out	10MHz from 50 Ohms, amplitude 2V pk-pk into 50 Ohms
External Ref In	10MHz into 50 Ohms, amplitude 2V pk-pk to 5V pk-pk
Output Level
Level Range	–110dBm to +7dBm (0.1μV to 500mV into 50 Ohms)
Setting Resolution	0.1dB (or 0.01μV to 1mV) by direct keyboard entry, or in user-set increments of 0.1dB to 100dB (or 0.01μV to 100mV)
Accuracy	Better than ± 2dBm
Harmonics	<-25dBc at +7dBm. <-30dBc@levels <=0dBm 30 to 6000MHz, <-25dBc@levels <=0dBm 10 to 30MHz
Sub-Harmonics	<3000MHz : None. >3000MHz :<–40dBc (typ) @ +7dBm
Non-Harmonic Spurii	<–50dBc >10kHz offset 10 to 3000MHz,10kHz offset 3000MHz to 6000MHz
Output Connector	Type N
Sweep	Frequency and amplitude sweep
Step Sweep	Step frequency and/or amplitude according to a formula over a specified number of points
Dwell Time	Individually programmable 0.01 to 10.000sec per step
Max Points	1000
Sweep Run	Continuous or single. Sweep up or down
Step Spacing	Linear or logarithmic
Sweep Triggering	Manual, Ext. signal, timed (0.1 – 999.9sec) or via remote interface
Sync Signal	Output Stable) available during dwell time. Programmable as high or low
List Sweep	As for Step Sweep except that a user defined table of frequency, amplitude and dwell time values defines the steps. The table can be created within the instrument or downloaded via the remote interfaces
Max Points	1000
List Storage	Up to 16 Sweep Lists can be stored permanently within the instrument
Point Trigger	Each point in a sweep (step or list) can be subject to a trigger event rather than a dwell time. Trigger by Manual, Ext. signal or via remote interface
Trim	(User Level Compensation Tables)
Function	A table of frequency/gain pairs allows the user to modify the generator output level with respect to frequency to calibrate an entire test set up or improve the calibration of the generator alone
Max Points	100
Interfaces	Full digital remote control through the RS232, USB, LAN and GPIB interfaces
RS-232	9-pin D connector. Variable Baud rate 1200 and 115200 Baud
USB	USB 2.0 connection. Operates as a virtual COM port
GPIB (IEEE-488)	Conforming with IEEE488.1 and IEEE488.2
LAN (Ethernet)	Standard 10/100 base-T hardware connection. ICMP and TCP/IP Protocol
General
Size and Weight	2U (86.5mm) height; half-rack (213mm) width; 350mm long. 3.65 kg. (8 lb)
Power	110-240VAC ±10% 50/60Hz; 100-120VAC ±10% 400Hz; 60VA max
Approvals	Complies with EN 61010-1 (Safety) and EN61326 (EMC)

随附

Operating manual, driver software, power lead

TGR6000信号发生器,英国tti TGR6000：

zui大频率	6000MHz
	zui小频率	10 兆赫
	分辨率	0.1 dB
	扫描	线性，对数
	接口类型	GPIB，LAN，RS232，USB
	尺寸	350 x 213.5 x 86.5mm
	zui高工作温度	+40°C
	型号（P）	TGR 6000
	高度	86.5mm
	插头类型	Type C - European Plug, Type G - British 3-pin
	重量	3.65kg
	zui低工作温度	+5°C
	长度	350mm
	数据输入	键盘
	输入	交流输入，参考输入，触发输入
	宽度	213.5mm
	显示器类型	20个字符´4行